Sadolin Shed & Fence Grey Shadow 5lt

You can apply this opaque shed and fence treatment from the Ronseal Fence life range to all rough sawn and smooth planed sheds and fences, using a brush, to colour and provide protection. It takes 1 hour to dry and will cover up to 6 m² per litre on average.Guarantee - StatutorySuitable for WoodWaterproofSurface Preparation - Fence Life Plus can be applied when the wood is damp, but not wet. So if it’s rained on the day of application, you need to wait for five hours before putting it on. The treatment can’t be applied in the rain. It needs to be a warm, dry day with temperatures above 10°C. Cold weather will stop it from drying. Clean the wood with a stiff brush to remove any dirt.Instructions for Use - Fence Life Plus can be applied with either a brush or sprayer. When brushing, check that you’re happy with the colour by applying it to a small hidden patch and leaving it to dry. If you are happy with the colour, get loads of Fence Life Plus on your brush. Apply a thick coat. Leave four hours for the first coat to dry. Check the fence to see if you need to apply another. When spraying, pour the Fence Life Plus into the tank. Pump up your sprayer or turn it on and start spraying. Use long, sweeping horizontal arm movements. Move along the full width of the fence panel, drop down and do the same again. Overlap each pass by 50% for the best coverage.Features and benefitsColour lasts for up to five yearsProtects in all weatherRainproof in 1 hourFor all sheds and fencesCan be applied using a brush or sprayer and to damp woodRonseal fence life plus+ can be used on all rough sawn and smooth planed sheds and fences. It'll stand up to rain, frost and snow and won't lose its colour in the sun. With 2 coats on rough sawn or 3 coats on smooth planed wood the colour will last for up to 5 years. Even better, you have the choice to brush it or spray it on and it can be applied to damp wood.

You can apply this opaque shed and fence treatment from the Ronseal Fence life range to all rough sawn and smooth planed sheds and fences, using a brush, to colour and provide protection. It takes 1 hour to dry and will cover up to 6 m² per litre on average.Guarantee - StatutorySuitable for WoodWaterproofSurface Preparation - Fence Life Plus can be applied when the wood is damp, but not wet. So if it’s rained on the day of application, you need to wait for five hours before putting it on. The treatment can’t be applied in the rain. It needs to be a warm, dry day with temperatures above 10°C. Cold weather will stop it from drying. Clean the wood with a stiff brush to remove any dirt.Instructions for Use - Fence Life Plus can be applied with either a brush or sprayer. When brushing, check that you’re happy with the colour by applying it to a small hidden patch and leaving it to dry. If you are happy with the colour, get loads of Fence Life Plus on your brush. Apply a thick coat. Leave four hours for the first coat to dry. Check the fence to see if you need to apply another. When spraying, pour the Fence Life Plus into the tank. Pump up your sprayer or turn it on and start spraying. Use long, sweeping horizontal arm movements. Move along the full width of the fence panel, drop down and do the same again. Overlap each pass by 50% for the best coverage.Features and benefitsColour lasts for up to five yearsProtects in all weatherRainproof in 1 hourFor all sheds and fencesCan be applied using a brush or sprayer and to damp woodRonseal fence life plus+ can be used on all rough sawn and smooth planed sheds and fences. It'll stand up to rain, frost and snow and won't lose its colour in the sun. With 2 coats on rough sawn or 3 coats on smooth planed wood the colour will last for up to 5 years. Even better, you have the choice to brush it or spray it on and it can be applied to damp wood.

You can apply this opaque shed and fence treatment from the Ronseal Fence life range to all rough sawn and smooth planed sheds and fences, using a brush, to colour and provide protection. It'll stand up to rain, frost and snow and won't lose its colour in the sun. With 2 coats on rough sawn or 3 coats on smooth planed wood the colour will last for up to 5 years. Even better, you have the choice to brush it or spray it on and it can be applied to damp wood. FenceLife Plus takes 1 hour to dry and will cover up to 6m² per litre on average.Guarantee - StatutorySuitable for WoodWaterproofSurface Preparation - Fence Life Plus can be applied when the wood is damp, but not wet. So if it’s rained on the day of application, you need to wait for five hours before putting it on. The treatment can’t be applied in the rain. It needs to be a warm, dry day with temperatures above 10°C. Cold weather will stop it from drying. Clean the wood with a stiff brush to remove any dirt.Instructions for Use - Fence Life Plus can be applied with either a brush or sprayer. When brushing, check that you’re happy with the colour by applying it to a small hidden patch and leaving it to dry. If you are happy with the colour, get loads of Fence Life Plus on your brush. Apply a thick coat. Leave four hours for the first coat to dry. Check the fence to see if you need to apply another. When spraying, pour the Fence Life Plus into the tank. Pump up your sprayer or turn it on and start spraying. Use long, sweeping horizontal arm movements. Move along the full width of the fence panel, drop down and do the same again. Overlap each pass by 50% for the best coverage.Features and benefitsColour lasts for up to five yearsProtects in all weatherRainproof in 1 hourFor all sheds and fencesCan be applied using a brush or sprayer and to damp wood

Ronseal 5 Year Fence Life+ Shed & Fence Protector provides 5 years of protection for your shed and fence with just two coats. It's simple to use and stands up to all kinds of weather. The first coat protects, and the second coat seals, giving you up to 5 years of deep, rich colour with no peeling or flaking. Sage gives your fence or shed a soft green finish that fits naturally with plants and borders. It’s a simple, calm shade that helps the garden feel tidy and consistent. Fence Life Plus+ can be used on all rough sawn and smooth planed wood whether its new, stained with a similar colour, or even damp.Suitable for WoodWaterproofSurface Preparation - Wait for a warm, dry day (above 10 °C and not going to rain). Cold, wet weather stops the stain from drying, which could make it wash off. Use a stiff brush to clean off any dirt and previous coatings that are peeling or flaking. Giving your wood a good clean makes sure the stain will soak in and stick properly. You could clean the wood with either a pressure washer (be careful not to damage the wood) or use a suitable fence cleaner. The stain is best applied to wood that is completely dry, however if your wood is damp to touch, then it can still be applied. Cover anything you don't want to get stain on. To check you're happy with the colour, find a small hidden patch of wood to test on before you paint your whole shed or fence.Instructions for Use - To apply with a brush, give it a really good stir. Use something wide, like an old wooden spoon. Get lots of the stain on your brush and put a good thick coat on. If you see any drips, brush them in. Give any drips on plants or paving a wipe with soapy water before the paint dries. On rough sawn wood, you'll need to use 2 coats to get 5 years protection. For smooth planed wood, you'll need to use 3 coats. leave 4 hours between coats. To apply using a sprayer, you'll need to make sure it's not too windy. Give the stain a really good stir, then pour the liquid into the tank. Pump it up or turn it on and start the spraying. Use long, sweeping. horizontal arm movements and move along the full width of the panel. Drop down and do the same again, going over again where you've already sprayed about half. This will make sure the whole area is covered with just the right amount of stain. On rough sawn wood, you'll need to use 2 coats to get 5 years protection. For smooth planed wood, you'll need to use 3 coats. leave 4 hours between coats. Any overspray should be cleaned up straight away with soapy water before it dries.

Ronseal 5 Year Fence Life+ Shed & Fence Protector provides 5 years of protection for your shed and fence with just two coats. It's simple to use and stands up to all kinds of weather. The first coat protects, and the second coat seals, giving you up to 5 years of deep, rich colour with no peeling or flaking. Charcoal Grey gives your fence or shed a strong, modern grey finish. It works well with most garden styles and keeps your wood looking smart and tidy. Fence Life Plus+ can be used on all rough sawn and smooth planed wood whether its new, stained with a similar colour, or even damp.Suitable for WoodWaterproofSurface Preparation - Wait for a warm, dry day (above 10 °C and not going to rain). Cold, wet weather stops the stain from drying, which could make it wash off. Use a stiff brush to clean off any dirt and previous coatings that are peeling or flaking. Giving your wood a good clean makes sure the stain will soak in and stick properly. You could clean the wood with either a pressure washer (be careful not to damage the wood) or use a suitable fence cleaner. The stain is best applied to wood that is completely dry, however if your wood is damp to touch, then it can still be applied. Cover anything you don't want to get stain on. To check you're happy with the colour, find a small hidden patch of wood to test on before you paint your whole shed or fence.Instructions for Use - To apply with a brush, give it a really good stir. Use something wide, like an old wooden spoon. Get lots of the stain on your brush and put a good thick coat on. If you see any drips, brush them in. Give any drips on plants or paving a wipe with soapy water before the paint dries. On rough sawn wood, you'll need to use 2 coats to get 5 years protection. For smooth planed wood, you'll need to use 3 coats. leave 4 hours between coats. To apply using a sprayer, you'll need to make sure it's not too windy. Give the stain a really good stir, then pour the liquid into the tank. Pump it up or turn it on and start the spraying. Use long, sweeping. horizontal arm movements and move along the full width of the panel. Drop down and do the same again, going over again where you've already sprayed about half. This will make sure the whole area is covered with just the right amount of stain. On rough sawn wood, you'll need to use 2 coats to get 5 years protection. For smooth planed wood, you'll need to use 3 coats. leave 4 hours between coats. Any overspray should be cleaned up straight away with soapy water before it dries.

Ronseal One Coat Shed & Fence Protection for sheds & fences. Don't waste more time than you need painting your shed and fence. One coat's easy to use, it can be brushed or sprayed on and it'll stand up to rain, frost, snow and sun, meaning you'll get lasting colour and protection for 2 years.Suitable for WoodWaterproofSurface Preparation - Before you start, wait for a warm, dry day (above 10c and not going to rain). Cold, wet weather stops the stain from drying which could make it wash off. Give the wood a good clean with a stiff brush to get rid of any dirt or the stain might not soak in properly. If your fence is grey and hasn't been treated before, you'll need to give the wood a good clean or the stain might not stick. You could clean the wood with either a pressure washer (be careful not to damage the wood) or use a suitable fence cleaner. The wood will need to be dry before you paint it. Cover anything you don't want to get stain on. To check you're happy with the colour, find a small hidden patch of wood to test on before you paint our whole shed or fence.Instructions for Use - When using a brush, give it a really good stir using something wide, like an old wooden spoon. Get lots of stain on your brush and put a good thick coat on. If you see any drips, brush them in. Give any drips on plants or paving a wipe with soapy water before it dries. When using a sprayer, you'll need to make sure it's not too windy. Pour the liquid into the tank. Pump it up and start spraying. Use long, sweeping, horizontal arm movements and move along the full width of the panel. Drop down and do the same again, going over where you've already sprayed by about half. This will make sure the whole area is covered with just the right amount of stain. Any overspray should be cleaned up straight away with soapy water before it dries.

Ronseal One Coat Shed & Fence Protection for sheds & fences. Don't waste more time than you need painting your shed and fence. One coat's easy to use, it can be brushed or sprayed on and it'll stand up to rain, frost, snow and sun, meaning you'll get lasting colour and protection for 2 years.Suitable for WoodWaterproofSurface Preparation - Before you start, wait for a warm, dry day (above 10c and not going to rain). Cold, wet weather stops the stain from drying which could make it wash off. Give the wood a good clean with a stiff brush to get rid of any dirt or the stain might not soak in properly. If your fence is grey and hasn't been treated before, you'll need to give the wood a good clean or the stain might not stick. You could clean the wood with either a pressure washer (be careful not to damage the wood) or use a suitable fence cleaner. The wood will need to be dry before you paint it. Cover anything you don't want to get stain on. To check you're happy with the colour, find a small hidden patch of wood to test on before you paint our whole shed or fence.Instructions for Use - When using a brush, give it a really good stir using something wide, like an old wooden spoon. Get lots of stain on your brush and put a good thick coat on. If you see any drips, brush them in. Give any drips on plants or paving a wipe with soapy water before it dries. When using a sprayer, you'll need to make sure it's not too windy. Pour the liquid into the tank. Pump it up and start spraying. Use long, sweeping, horizontal arm movements and move along the full width of the panel. Drop down and do the same again, going over where you've already sprayed by about half. This will make sure the whole area is covered with just the right amount of stain. Any overspray should be cleaned up straight away with soapy water before it dries.

Ronseal One Coat Shed & Fence Protection for sheds & fences. Don't waste more time than you need painting your shed and fence. One coat's easy to use, it can be brushed or sprayed on and it'll stand up to rain, frost, snow and sun, meaning you'll get lasting colour and protection for 2 years.Suitable for WoodWaterproofSurface Preparation - Before you start, wait for a warm, dry day (above 10c and not going to rain). Cold, wet weather stops the stain from drying which could make it wash off. Give the wood a good clean with a stiff brush to get rid of any dirt or the stain might not soak in properly. If your fence is grey and hasn't been treated before, you'll need to give the wood a good clean or the stain might not stick. You could clean the wood with either a pressure washer (be careful not to damage the wood) or use a suitable fence cleaner. The wood will need to be dry before you paint it. Cover anything you don't want to get stain on. To check you're happy with the colour, find a small hidden patch of wood to test on before you paint our whole shed or fence.Instructions for Use - When using a brush, give it a really good stir using something wide, like an old wooden spoon. Get lots of stain on your brush and put a good thick coat on. If you see any drips, brush them in. Give any drips on plants or paving a wipe with soapy water before it dries. When using a sprayer, you'll need to make sure it's not too windy. Pour the liquid into the tank. Pump it up and start spraying. Use long, sweeping, horizontal arm movements and move along the full width of the panel. Drop down and do the same again, going over where you've already sprayed by about half. This will make sure the whole area is covered with just the right amount of stain. Any overspray should be cleaned up straight away with soapy water before it dries.

Ronseal 5 Year Fence Life+ Shed & Fence Protector provides 5 years of protection for your shed and fence with just two coats. It's simple to use and stands up to all kinds of weather. The first coat protects, and the second coat seals, giving you up to 5 years of deep, rich colour with no peeling or flaking. Slate gives your fence or shed a clean grey finish with a modern look. It works with any style of garden and keeps the wood looking sharp and tidy. Fence Life Plus+ can be used on all rough sawn and smooth planed wood whether its new, stained with a similar colour, or even damp.Suitable for WoodWaterproofSurface Preparation - Wait for a warm, dry day (above 10 °C and not going to rain). Cold, wet weather stops the stain from drying, which could make it wash off. Use a stiff brush to clean off any dirt and previous coatings that are peeling or flaking. Giving your wood a good clean makes sure the stain will soak in and stick properly. You could clean the wood with either a pressure washer (be careful not to damage the wood) or use a suitable fence cleaner. The stain is best applied to wood that is completely dry, however if your wood is damp to touch, then it can still be applied. Cover anything you don't want to get stain on. To check you're happy with the colour, find a small hidden patch of wood to test on before you paint your whole shed or fence.Instructions for Use - To apply with a brush, give it a really good stir. Use something wide, like an old wooden spoon. Get lots of the stain on your brush and put a good thick coat on. If you see any drips, brush them in. Give any drips on plants or paving a wipe with soapy water before the paint dries. On rough sawn wood, you'll need to use 2 coats to get 5 years protection. For smooth planed wood, you'll need to use 3 coats. leave 4 hours between coats. To apply using a sprayer, you'll need to make sure it's not too windy. Give the stain a really good stir, then pour the liquid into the tank. Pump it up or turn it on and start the spraying. Use long, sweeping. horizontal arm movements and move along the full width of the panel. Drop down and do the same again, going over again where you've already sprayed about half. This will make sure the whole area is covered with just the right amount of stain. On rough sawn wood, you'll need to use 2 coats to get 5 years protection. For smooth planed wood, you'll need to use 3 coats. leave 4 hours between coats. Any overspray should be cleaned up straight away with soapy water before it dries.

Ronseal One Coat Shed & Fence Protection for sheds & fences. Don't waste more time than you need painting your shed and fence. One coat's easy to use, it can be brushed or sprayed on and it'll stand up to rain, frost, snow and sun, meaning you'll get lasting colour and protection for 2 years. One 950ml pouch makes 5L of Shed & Fence Protector.Suitable for WoodWaterproofSurface Preparation - Before you start, wait for a warm, dry day (above 10c). Clean the wood with a stiff brush. If your fence hasn't been treated before, clean it with either a pressure washer or a suitable fence cleaner, then let the wood dry before painting. Cover anything you don't want to get stain on. To check you're happy with the colour, find a small hidden patch of wood to test on. You'll need more coats for contrasting colour changes. If you're using this pouch to refill your ready mix one coat, the colour may look different when it's wet. But don't worry, it'll look the same when it dries.Instructions for Use - To mix, pour the pouch into a bucket. Fill the pouch with water, reseal & shake. Pouch holds 1 litre. Pour the pouch of water into the bucket. Mix well for 1 minute. For the first pour, add water gradually like making a cake. Add 3 more pouches of water by repeating each step, 3 times. Scrape bottom of bucket when mixing between pours. If you're using a brush, get lots of stain on your brush, then brush on a thick coat. Brush in any drips. Wipe any drips off plants or paving with soapy water before it dries. If you're using a sprayer, ensure it's not too windy. Mix the stain in a bucket and pour into the tank, Pump it up and start spraying. Use long, seeping, horizontal arm movements and move along the full width of the panel. Drop down and do the same again, overlapping by about half. Clean any overspray with soapy water before it dries.